Alternate source for Rocker Switches

A place to discuss the design & installation of electrical systems.
Post Reply
pequeajim
Class G
Posts: 24
Joined: Tue Feb 20, 2007 10:10 pm
Location: New Holland, PA

Alternate source for Rocker Switches

Post by pequeajim »

I am looking for some rocker switches to use in my airplane. I like what I have found at Gulf Coast Avionics, but they are pushing $39.00 each!

Here are some that are lighted and much less. What do you guys think?

http://search.instawares.com/lighted-ro ... ggodiiuhaa

Also, where do you shop for lighted rockers?

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

Jim,

My guess is that quality from a supplier like that will vary greatly.

Equipment like the ones in the food industry is so random when it comes to specs it is hard to determine what would be quality from a web page. I have worked with many of those switches and some are VERY durable. Some fail the next week.

Buy several and see which one seems the most durable.

:) CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

pequeajim
Class G
Posts: 24
Joined: Tue Feb 20, 2007 10:10 pm
Location: New Holland, PA

Post by pequeajim »

I would agree with you. Generally, I would think that something made for the industrial environment would be pretty robust?

Also, when you are woring your circuits, if you are powering two systems from a single switch, (like com and xponder), are you typically using a DPST?

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

No, you are using a single pole switch in that case. The wires are "T' connected downstream of the switch.

You know whatamean?

:) CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

pequeajim
Class G
Posts: 24
Joined: Tue Feb 20, 2007 10:10 pm
Location: New Holland, PA

Post by pequeajim »

captain_john wrote:You know whatamean?

:) CJ
Yep, I understand...

Typically then, what devices do you need a switch other than a single pole for?

Jim!

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

Well, there are many different switches out there for many different reasons.

For instance, let's say you want to have one switch for fuel pump and primer combined. Down=Off, Center=Boost Pump and Up (momentary contact) for primer. A very unique switch indeed!

Another scenario-to switch inputs to a device you need a single pole double throw (SPDT). This means one pole is thrown 2 ways. Usually the common is to the device you want to power and the other two wires could be from 2 other sources like microphone inputs to an intercom or GPS feeds to a common CDI.

A double pole can certainly be used like you suggest, but it is more costly and not necessary. If you needed to separate the loads but switch them simultaneously, the double pole would be a good way to do it.

Does this help?

:) CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

pequeajim
Class G
Posts: 24
Joined: Tue Feb 20, 2007 10:10 pm
Location: New Holland, PA

Post by pequeajim »

Yep, thanks for the insight.

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

You are welcome.

Have a look at some of the www.aeroelectric.com diagrams and you will see the variety of switches out there.

I know that reading schematics is like eating dry toast, but look for as long as you can take it.

Make note of the switch numbers and then locate them on the B and C Specialties website and compare them.

Let me know if you have any questions.

:) CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

Post Reply