Fuel tank roughing for pro-seal?

A forum in which to discuss topics that are not specific to a particular series of aircraft (ie. how to cut alclad)
Post Reply
RV7A
Class E
Posts: 85
Joined: Tue Jul 31, 2012 5:49 am
Location: Westland, MI
Contact:

Fuel tank roughing for pro-seal?

Post by RV7A »

I am ready to start pro-sealing my wing tanks together. I am wondering what grit sandpaper to use to rough up the areas where the parts get pro-sealed together?

From looking at pics online, it looks like people are roughing these areas up a lot-maybe 220 grit?

Thanks

User avatar
leffler
Class E
Posts: 188
Joined: Sat Sep 19, 2009 10:31 pm
Location: KDLZ
Contact:

Post by leffler »

I would say that a maroon scotchbrite pad is more commonly used than sandpaper.
Bob Leffler
RV-10 - Flying
http://mykitlog.com/rleffler

User avatar
bruceh
Class D
Posts: 393
Joined: Sun Apr 06, 2008 11:11 pm
Location: Ramona, CA
Contact:

Post by bruceh »

I taped off the surfaces that got sealant and went at it with the maroon scotchbrite pads. Clean the surfaces with a paper towel and acetone or MEK until there is no residue. Wear gloves so you don't contaminate the surfaces with your fingers. After you butter up the ribs and get them in place you can come back with a popsicle stick and put a nice smooth fillet of proseal up against each rib, then pull the tape for a nice and clean installation.

Lots of photos and tips on my web page.
Bruce Hill
RV-9A N5771H flying over 1100 hours!
Build Log at http://www.overthehills.com/RV-9A-Project
Blog at https://flyingoverthehills.wordpress.com/
EAA Tech Counselor, A&P

User avatar
bruceh
Class D
Posts: 393
Joined: Sun Apr 06, 2008 11:11 pm
Location: Ramona, CA
Contact:

Post by bruceh »

duplicate post....
Bruce Hill
RV-9A N5771H flying over 1100 hours!
Build Log at http://www.overthehills.com/RV-9A-Project
Blog at https://flyingoverthehills.wordpress.com/
EAA Tech Counselor, A&P

User avatar
BSwayze
Class C
Posts: 581
Joined: Wed Jun 27, 2007 5:15 am
Location: Portland, Oregon
Contact:

Post by BSwayze »

I bought a slotted scotchbrite pad holder for my die grinder. It's the best tool for this! You cut strips of scotchbrite, slide one into the slot, and tighten the retainer nut. Tape off areas you don't want scuffed up, as others have said, and this will get the job done in a hurry. I went at it one direction, then again at a 90° angle. Then clean it thoroughly as Bruce said.

Image

Image
Bruce Swayze
Portland, Oregon
http://www.BrucesRV7A.com
RV-7A Working on Firewall Forward

DaAV8R
Class G
Posts: 48
Joined: Thu Mar 15, 2012 9:35 pm
Location: Missouri

Where from?

Post by DaAV8R »

Well I'll be a monkey's uncle.

Bruce....Where did you get that? Even though I'm about done scuffing parts, I think I want one. It just seems like a guy ought to own the tool that could have saved him about 30 man hours. Let me guess, it's $1.39 :)

What other tools are you keeping secret that might save a few hundred hours?

For large areas I have been using a full scotchbrite sheet under a vibrating sander. Gets a large area done in short order.

Robert

User avatar
TomNativeNewYorker
Class D
Posts: 439
Joined: Tue Mar 21, 2006 9:19 pm
Location: KSAV

Re: Where from?

Post by TomNativeNewYorker »

DaAV8R wrote: Bruce....Where did you get that? Even though I'm about done scuffing parts, I think I want one. It just seems like a guy ought to own the tool that could have saved him about 30 man hours. Let me guess, it's $1.39 :)
3M makes those mandrels for scotch brite strips.

I have the federal NSN numbers for anyone who can order through the federal supply system

User avatar
TomNativeNewYorker
Class D
Posts: 439
Joined: Tue Mar 21, 2006 9:19 pm
Location: KSAV

Post by TomNativeNewYorker »


User avatar
BSwayze
Class C
Posts: 581
Joined: Wed Jun 27, 2007 5:15 am
Location: Portland, Oregon
Contact:

Re: Where from?

Post by BSwayze »

DaAV8R wrote:Bruce....Where did you get that? Even though I'm about done scuffing parts, I think I want one. It just seems like a guy ought to own the tool that could have saved him about 30 man hours. Let me guess, it's $1.39 :)
Robert
Robert, sorry it took me a little while here. I couldn't remember for sure where I got it or what I paid. So I pulled a file of receipts I keep for all my tool purchases and looked it up. My memory was hazy but correct, Cleaveland Tools carries this item. Here's a link that should take you right to it:

http://www.cleavelandtool.com/prodinfo. ... ber=3MM300

Sadly, it did cost a bit more than $1.39. Ha! My receipt shows that I bought it in August 2006 and paid $5.50 for it! The price seems to have gone up quite a bit since then, but still a good tool to have, I think. I used it in other areas along the way, but it was most useful inside the fuel tank skins as I showed earlier. :)
Bruce Swayze
Portland, Oregon
http://www.BrucesRV7A.com
RV-7A Working on Firewall Forward

Post Reply