Page 1 of 1
Who's gonna be building hard over Christmas??
Posted: Sat Dec 08, 2007 3:54 pm
by RV9inIowa
ME ME ME!
My wings are stored and the SB fuse kit will be here by Friday! Santa's coming with his ABF truck!
Like my precision engineered wing cradle? The other end has carpet straps to hold the wing. Total cost = $20. It will soon be up against the wall with a wood panel on the outside (to hang fuselage drawings on).
I Hope all of you have a very Merry Christmas,
dave
Posted: Sat Dec 08, 2007 5:36 pm
by cjensen
That's great Dave! I will be in the "Not doing anything" category over Christmas. Fuselage done, finish kit arrival end of January. Bummer. Your wings look great! Have fun geting the fuselage going! It's A LOT of fun!!
Posted: Sat Dec 08, 2007 6:29 pm
by smittysrv
Very cool Dave!
I have the order form filled out for my fuselage. Gotta' beat them price increases. It should go next week (pay day).
Posted: Sat Dec 08, 2007 7:54 pm
by Lorin Dueck
Not me. I'm working hard on my priorities.
My 14 YO son is coming out to California from VA.
Hoping to make this a special Xmas.
Lorin D.
PS - Smitty great job on the flap (saw it on th'other site).
Keep up the good work!!
Posted: Sat Dec 08, 2007 8:06 pm
by bullojm1
smittysrv wrote:Very cool Dave!
I have the order form filled out for my fuselage. Gotta' beat them price increases. It should go next week (pay day).
Smitty...
Rumor (confirmed by Van's) has it for 2008 Van's isn't hiking their prices until Feb 1.
Posted: Sun Dec 09, 2007 7:30 am
by smittysrv
Rumor (confirmed by Van's) has it for 2008 Van's isn't hiking their prices until Feb 1.
Not until Feb 1st? Verrrry Interesting...
Dont tell my wife!!
Posted: Sun Dec 09, 2007 3:55 pm
by Spike
Very Niiiice!!
Posted: Mon Dec 10, 2007 11:02 am
by Womack2005
I'll be in Florida playing golf!
BUT...I was in the shop most of this last weekend
Its been so long since I worked on this thing that my PR has expired
I had to get some more from work.
Posted: Mon Dec 10, 2007 11:40 am
by tmbg
I'm working my butt off now! I had taken way too long a hiatus after my accident, and now I'm desperately trying to finish up my left fuel tank so I can put the left wing to bed...
I have all the interior ribs installed, sealed, and filleted. Vent line is in, cap plates are in, wiring's in. Need to install the end ribs, flop tube, and wire the cap senders to the BNC connector, then install the baffle and Z-brackets, then no more proseal for awhile! hooray!
Posted: Mon Dec 10, 2007 11:47 am
by dons
I expect I'll get a little bit of time to work on wings, it may only be 2 days off, but every little bit adds up. I did all the corrosion protection on my wing ribs yesterday, is it every a good feeling to finally get that done.
I like that wing cradle Dave.
2.5 weeka
Posted: Sat Dec 15, 2007 11:07 pm
by weezbad
probally spend all of it wiring and clamping up front. two dynons, sl30,gtx 327, intercom, and various other toys. also finalizing my fuel flow transducer set up when i get soem more supplies. maybe hunt a day ot two.