Fuel tank leak fix thread

A place to chuckle at yourself and share lessons learned the hard way.
User avatar
hydroguy2
Class B
Posts: 1307
Joined: Mon Sep 10, 2007 11:13 pm
Location: Townsend, Montana

Post by hydroguy2 »

good work Dude.

note to self: if needed, fuel tank leaks can be repaired by inviting Chad to Montana.
Brian
Townsend, MT

Spike
Chief Rivet Banger
Posts: 4013
Joined: Thu Oct 14, 2004 8:40 pm
Location: Baltimore, MD
Contact:

Fuel tank leak fix thread

Post by Spike »

Or a matchbook and insurance check ....

-- Spike

Submitted via email

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Yeah...I gotta tells ya dude, this SUCKED!! If it leaks again, I like the matchbook idea... :lol:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

The tank is back on and it's a beautiful day!! Flying is on the afternoon schedule!
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

The good news: My fix for the leak I had is good.

The bad news: I went to fly over lunch today, and fuel is dripping...I mean DRIPPING, from the same fuel tank. I called my dad, he ran out to the airport to help me drain all 21 gallons in to five buckets, and quickly pull the tank...AGAIN!! :bang:

My fuel sender is now leaking. Worse than the original leak. Should be an easier fix than what I went thru two weeks ago, but STILL!! DAMMIT!!!

:x
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
hydroguy2
Class B
Posts: 1307
Joined: Mon Sep 10, 2007 11:13 pm
Location: Townsend, Montana

Post by hydroguy2 »

Holy crap, batman! that really sucks.
Brian
Townsend, MT

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Evening update...I took the sender out completely, cleaned it up, and reinstalled with the new style rubber gasket (MUCH thinner than before), and also put gaskets under the screw heads. This is sort of a cross between Piper and Cessna sender methods. The guys at work thought this to be the best solution, and so far, the tank is holding fuel once again...

How I had it installed before...sealant gooped all around the base plate after the thick rubber gasket was squeezed out too far (my fault).

Image

And how it now looks tonight...

Image

Much cleaner!
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
bullojm1
Chief Rivet Banger
Posts: 1357
Joined: Sat Mar 25, 2006 6:37 pm
Location: KDMW
Contact:

Post by bullojm1 »

Chad,

Just curious, but did you perform a pressure check on your tank before you installed it? Or did you just leave fuel in the top of it?

Lucky it was an easy fix!
Mike Bullock
http://www.rvplane.com
RV-7 | Superior IO-360 | Whirlwind 200RV
Garmin GTN650 | GRT Dual Sport SX EFIS
Status: FLYING!

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Just fuel, no pressure test. I don't think it would have mattered because the sealant around the sender failed sometime between last night and today at lunch. I was in the hangar yesterday checking for leaks and all was well. Fuel finally worked it's way under the rubber gasket and popped the sealant off. The way it was dripping today, it had to have happened over night or this morning. It was dripping at a rate of once every two seconds.

I really think it would've passed a leak test last week when I finished the reseal.
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
hydroguy2
Class B
Posts: 1307
Joined: Mon Sep 10, 2007 11:13 pm
Location: Townsend, Montana

Post by hydroguy2 »

Chad, did you just use the "blank" sender covers for access during this repair? Did you use any kind of doubler with the nutplates or not?

I have to remove some slosh from some RV-4 tanks and am trying to decide if I should cut holes like you did, or try to pop the rear baffle off completely.
Brian
Townsend, MT

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Brian and I talked off of RB about this, but just so the question is answered for all, I did use blank covers for this repair, but no doublers for nutplates.

Popping the rear baffle off isn't necessary, though access is MUCH better...just a lot more work to seal back up and prevent leaks.

8)
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

Hey Bri, I think Vlad used his hubcaps that come with the finish kit to blank off some holes that he cut in his tank(s). VERY RESOURCEFUL!

:) CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

User avatar
hydroguy2
Class B
Posts: 1307
Joined: Mon Sep 10, 2007 11:13 pm
Location: Townsend, Montana

Post by hydroguy2 »

But I don't have 6 hubcaps
Brian
Townsend, MT

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

Hmmmm, lean on our fellow builders!

Put out an all call!

:wink: CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

Post Reply