Fuel tank leak fix thread

A place to chuckle at yourself and share lessons learned the hard way.
User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Fuel tank leak fix thread

Post by cjensen »

I don't have a lot of time right now, but I'll throw out some pics from this morning's tank removal...thankfully it rained all morning!

Here are a couple of pics of the leaking areas...the bottom-
Image

...and the top where the red hash marks are-
Image

Tank bolts removed...this was a PAIN IN THE ASS. It sucked. Period. :x
Image

Staining on the spar-
Image

The leak on the TOP of the tank, extends between the red arrows-
Image

Image

Image

Image

This was interesting to find, but not terribly unexpected with SW float senders...it has a small leak at the sender screw itself. Not a whole lot I can do about that unless I replace it-
Image

Sad pic...
Image

So tomorrow I plan to cut holes in the rear baffle... :bang:

It's not as bad as I was expecting to see, but now I am TOTALLY dreading putting those tank bolts back in when I'm done.

Gotta run...more later!
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

Spike
Chief Rivet Banger
Posts: 4013
Joined: Thu Oct 14, 2004 8:40 pm
Location: Baltimore, MD
Contact:

Fuel tank leak fix thread

Post by Spike »

Woooow dude. This is my biggest fear. I fought my tanks, one of them especially. 

Please make sure you vent that tank thoroughly before exposing it to any tools that could act as an ignition source.

Spike

Sent via DROID on Verizon Wireless


-----Original message-----
From: RB Lists - Screwup Chronicles <support@rivetbangers.com>
To:
screwup@rivetbangers.com
Sent:
Sat, Oct 23, 2010 20:11:38 GMT+00:00
Subject:
Fuel tank leak fix thread



I don't have a lot of time right now, but I'll throw out some pics from this morning's tank removal...thankfully it rained all morning! Here are a couple of pics of the leaking areas...the bottom- Image ...and the top where the red hash marks are- Image Tank bolts removed...this was a PAIN IN THE ASS. It sucked. Period. Image Image Staining on the spar- Image The leak on the TOP of the tank, extends between the red arrows- Image Image Image Image This was interesting to find, but not terribly unexpected with SW float senders...it has a small leak at the sender screw itself. Not a whole lot I can do about that unless I replace it- Image Sad pic... Image So tomorrow I plan to cut holes in the rear baffle... Image It's not as bad as I was expecting to see, but now I am TOTALLY dreading putting those tank bolts back in when I'm done. Gotta run...more later!Chad Jensen N755CB|RV-7|Flying RV-7 Build Log rivetbangers.com - Discussion topic http://www.rivetbangers.com/forums/viewtopic.php?p=35315#35315
Submitted via email

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Air tools only...shop rule at work (where I'll be working on it) when working with fuel tanks... :wink:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Today was cutting day...but first, I started by removing the inspection panel on the inboard rib by taking out the screws, giving a good slice thru the sealant with a knife, and it popped right off...

Image

Then it was time. Time to use everyone's favorite tool...the fly cutter. I have to say that I was quite pleased with how this worked out. I was dreading it because of the fly cutter's reputation for grabbing stuff and flinging it across rooms. This was a breeze actually...other than needing ear plugs to mute the squeal of the cutter.

Image

Three holes cut at 5" and one at 3.75" all cleaned up.

Image

I took a few pictures of the "bead" that was there from when I built the tanks. I actually didn't think it would look as good as it did, but it obviously wasn't good enough. One pic is good enough to show what each bay looked like.

Image

From what I've read, almost everyone says to keep the working hole as small as possible...why? I don't know...less surface area to reseal later? Anyway, it was gonna be hard enough/messy enough as it was, so my larger 5" holes aided in maneuverability to get the sealant spread. It's still a mess in there, but the fillet is nice and smooth on the top and bottom...

Image

And then the thread had to be ruined by some crazy dude peaking thru a hole at you... :P

Image

I'll let that setup until tomorrow night, and then check things over. I may put a small amount of fuel in the tank and tip it so it doesn't spill out of the working holes to check for leaks along the baffle seam before I seal the patch covers in place. :headscratch:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

Spike
Chief Rivet Banger
Posts: 4013
Joined: Thu Oct 14, 2004 8:40 pm
Location: Baltimore, MD
Contact:

Post by Spike »

Thanx for the pics. How do you plan on plugging those holes in the back? Are you going to do a similar design as the fuel sender panel?

Spike
http://www.rivetbangers.com - Now integrating web and mail!
Current Build: 2 years into a beautiful little girl

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Yep, it'll end up looking just like this...

Image
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

Spike
Chief Rivet Banger
Posts: 4013
Joined: Thu Oct 14, 2004 8:40 pm
Location: Baltimore, MD
Contact:

Post by Spike »

Nice. Blind rivets or screws for those panels?

Spike
http://www.rivetbangers.com - Now integrating web and mail!
Current Build: 2 years into a beautiful little girl

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Screws...they'll be done just like the side access panel. I just ordered the panels and gaskets from the web store. I'll have to make a panel and gasket for the smaller hole tho...
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

I'll know more in the morning...

Image

Image

:popcorn:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
hydroguy2
Class B
Posts: 1307
Joined: Mon Sep 10, 2007 11:13 pm
Location: Townsend, Montana

Post by hydroguy2 »

good luck.

put some papertowel or white sheet under it. IF...fingers crossed it doesn't, but IF you have a leak you'll be able to track it down better.
Brian
Townsend, MT

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Great idea...unfortunately, I'm already home, plopped on the couch watching the Series!! Just hoping for the best!
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

Keep in mind, you will have a fair amount of evaporation overnight.

It's amazing how fast 100LL evaporates!

:o CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Yeah, the guys told me to expect it to be 1/4-1/2" down by morning. :o

What a waste of good <expensive> fuel this is... :roll:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

Finally had some time to get back to the tank last night. I didn't quite get to sealing the covers, but the plate nuts are in, and I plan to have my own private sealant party tonight... :bang:

Image

8)
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
hydroguy2
Class B
Posts: 1307
Joined: Mon Sep 10, 2007 11:13 pm
Location: Townsend, Montana

Post by hydroguy2 »

Party? by yourself? you're an animal
Brian
Townsend, MT

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

hydroguy2 wrote:Party? by yourself? you're an animal
I know! It's gonna be SO fun! :lol:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

My party is over...but the good news is, the sealant is on and curing!

Image

Image

Prayer beads are out...hoping for the best for an overnight test tomorrow!

Man I hope to be flying again this weekend!
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

Spike
Chief Rivet Banger
Posts: 4013
Joined: Thu Oct 14, 2004 8:40 pm
Location: Baltimore, MD
Contact:

Post by Spike »

Good news Chad. Let us know know how the test goes. I hope I don't have to go through this.

Spike
http://www.rivetbangers.com - Now integrating web and mail!
Current Build: 2 years into a beautiful little girl

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

For your sake, I hope you don't either! I hope I'm done with this!!

'Course, if it doesn't leak, I have to plan on a half day of swearing at the tank to get it reinstalled...not looking forward to THAT!
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

User avatar
cjensen
Whiskey Victor
Posts: 5275
Joined: Sat Apr 23, 2005 10:36 pm
Location: Green Bay, WI

Post by cjensen »

The tank has been holding fuel since 9am this morning...fingers still crossed, but it's looking pretty good!

:thumbsup:
Chad Jensen
Missing my RV-7...
Vertical Power support
920.216.3699
http://verticalpower.com

Post Reply