pop rivet question?

Joe Casey · Post by **Joe Casey** » Thu Dec 27, 2007 2:53 pm

When I did my inventory, I recorded the bag numbers on the pop rivets, and now cannot tell which is which... Is the cad plated pop rivet used for the fiberglass parts the CS4-4 as shown on the plans?

Kenk · Post by **Kenk** » Thu Dec 27, 2007 3:10 pm

I believe the cad plated rivets were the "oops" rivets. There is a page near the front of the manual that lists the various rivets with pictures.

----- Original Message -----
From: RB Lists - RV9 (support@rivetbangers.com)
To: rv9@rivetbangers.com (rv9@rivetbangers.com)
Sent: Thursday, December 27, 2007 1:53 PM
Subject: pop rivet question?

When I did my inventory, I recorded the bag numbers on the pop rivets, and now cannot tell which is which... Is the cad plated pop rivet used for the fiberglass parts the CS4-4 as shown on the plans?

rivetbangers.com - Discussion topic http://www.rivetbangers.com/cgi-php/forums/viewtopic.php?p=22673#22673

Submitted via email

smittysrv · Post by **smittysrv** » Thu Dec 27, 2007 3:49 pm

Hope this helps:

Post by **bullojm1** » Thu Dec 27, 2007 4:01 pm

Smitty-

Wow, great pics of the pop rivets! You mind if I steal them and put them on my web log?

smittysrv · Post by **smittysrv** » Thu Dec 27, 2007 4:11 pm

No prob! Sorry bout' the fuzzy one.

Joe Casey · Post by **Joe Casey** » Thu Dec 27, 2007 4:46 pm

I am absolutely speechless at how quick I not only get an answer, but pics too!!! thanks Smitty....
Joe Casey

svanarts · Post by **svanarts** » Thu Dec 27, 2007 11:54 pm

And not one person flamed you for asking "a dumb question." Which, it wasn't. But on other forums, that would probably have happend. Here you get answers with pictures. Ain't this a great place?

Heck, I'm going to bookmark this thread because half the time I can't tell them buggers apart myself.

RV7Factory · Post by **RV7Factory** » Fri Dec 28, 2007 1:01 am

Wow Smitty above and beyond! Great stuff.

I don't want to detract from Smitty's fine work, but as Kenk said there is a blind rivet identification chart in the manual. Page 5-16.

JOHN TIPTON · Post by **JOHN TIPTON** » Fri Dec 28, 2007 1:08 pm

Hi Guys

Re: Duckworks Landing Lights

As a matter of interest, what are the 'soft' POP rivets that can be used for the mounting strips to the lens on these units, I'm going down this road as opposed to the double sided sticky tape

John

captain_john · Post by **captain_john** » Sat Dec 29, 2007 7:50 am

The pop rivets that come with the Duckworks kits are for retrofitting the kit into a QB Wing.

CJ

Cherokee Driver · Post by **Cherokee Driver** » Sat Dec 29, 2007 1:42 pm

I see Kenk is a new member...

Also glad to see another SE Wisconsin builder in the forum.

CD

Kenk · Post by **Kenk** » Sat Dec 29, 2007 2:48 pm

Thank you. I have been a passive reader for a couple of years. Great site!
Am building an RV-9, small wheel in the rear.
KenK

----- Original Message -----
From: RB Lists - RV9 (support@rivetbangers.com)
To: rv9@rivetbangers.com (rv9@rivetbangers.com)
Sent: Saturday, December 29, 2007 12:42 PM
Subject: pop rivet question?

I see Kenk is a new member...

Also glad to see another SE Wisconsin builder in the forum.

CD

Emp Kit RV-8/8A

Home of "Skunk Works, Wisconsin Branch"
"Glacial Pace...but lovin every minute of it!"

rivetbangers.com - Discussion topic http://www.rivetbangers.com/cgi-php/forums/viewtopic.php?p=22758#22758

Submitted via email

RivetBangers.com