Cockpit paint

A forum in which to discuss topics specific to the assembly of the RV 9/9A
Post Reply
JOHN TIPTON
Class E
Posts: 92
Joined: Thu Jun 08, 2006 4:46 pm
Location: Torquay England

Cockpit paint

Post by JOHN TIPTON »

Hi Guys

What's the best finish (paint options) for the cockpit (RV9a QB)

Regards

John

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

I used Dupont Nason. It is an automotive grade urethane over epoxy primer. On small parts and the glareshield i used rustoleum hammer finish in the rattle can.

Worked for me!

:) CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

User avatar
plbarrett2004
Class E
Posts: 57
Joined: Tue Dec 18, 2012 7:47 am
Location: KDMW
Contact:

Post by plbarrett2004 »

I'm using automotive Delfleet Essential two part epoxy primer, and corresponding paint, for my interior. Some people use the jet flex or other aviation specific paints, but in my judgment they are more trouble than they are worth. I have yet to meet a builder who used rustoleum rattle can paint and regretted that decision. If I had not already bought the delfleet paint, I'd probably use the rattle can paint. Super easy to fix and match in the future too!

Cheers,
Peter
Peter Barrett
CFI, CFII, MEI
RV-8 Fastback - Fuselage in progress
Build Log @ papalimabravo.com
SEMPER FIDELIS

User avatar
bullojm1
Chief Rivet Banger
Posts: 1357
Joined: Sat Mar 25, 2006 6:37 pm
Location: KDMW
Contact:

Post by bullojm1 »

My interior paint is water-reducible JetFlex over top of rattle can NAPA 7220 grey primer. The paint was very thick and hard to apply perfectly without getting an orange-peel finish. Additionally, it liked to clog my paint gun. The nice part about the WR paint is cleanup is a breeze with using warm water. It has held up extremely well over the last 5 years and 350 hours.
Mike Bullock
http://www.rvplane.com
RV-7 | Superior IO-360 | Whirlwind 200RV
Garmin GTN650 | GRT Dual Sport SX EFIS
Status: FLYING!

User avatar
captain_john
Sparky
Posts: 5880
Joined: Sun Oct 31, 2004 9:17 am
Location: KPYM

Post by captain_john »

350 hours in 5 years?!?

I hear that some people do that in one year!

:wink: CJ
RV-7
Garmin G3X with VP-X & a TMX-IO-360 with G3i
It's all over but the flying! 800+ hours in only 3 years!

User avatar
bullojm1
Chief Rivet Banger
Posts: 1357
Joined: Sat Mar 25, 2006 6:37 pm
Location: KDMW
Contact:

Post by bullojm1 »

captain_john wrote:350 hours in 5 years?!?

I hear that some people do that in one year!

:wink: CJ
Not all of us get the summer off! :cry: :cry:
Mike Bullock
http://www.rvplane.com
RV-7 | Superior IO-360 | Whirlwind 200RV
Garmin GTN650 | GRT Dual Sport SX EFIS
Status: FLYING!

User avatar
BSwayze
Class C
Posts: 581
Joined: Wed Jun 27, 2007 5:15 am
Location: Portland, Oregon
Contact:

Post by BSwayze »

I, too, used the water-based JetFlex interior paint. I love it. It's thick, that's true, but it sprays just fine. I thinned it with just a bit of distilled water (about 10%) and turned up the air pressure on my sprayer and with a little experience, got it to work just fine. There's a list of things that I really like about this paint:

There's no odor. So I didn't need a booth, air masks, fans or filters. I just painted in my garage or outside, no problems. No complaints from my wife or neighbors. I painted most of my interior parts before riveting them together. I highly recommend this.

If you mess something up, you can just wash it off and do it over (if you do it right away before it starts drying).

Cleanup is a breeze. Warm soapy water in the sink. No thinners, fumes, etc. to worry about.

It takes longer to get a good, hard cure, but when it's dry, you get a non-reflective satin finish that cleans up easily when needed.

I figured if this was good enough for Boeing to buy by the truckload, it's good enough for me.
Bruce Swayze
Portland, Oregon
http://www.BrucesRV7A.com
RV-7A Working on Firewall Forward

Post Reply